Perma-grit Rotary Files for Dremel Proxxon etc



Narrow Cone (Ref: RF1.)

Narrow Cone

Available in Fine or Coarse

Small Rotary
Small Rotary Narrow Cone Fine finishing Grit, base 8 mm (widest point). Shaft / arbor 3.1 mm (1/8").
Drills own pilot hole. Make and enlarge holes.


The FINE ROTARIES enables the user to cut thin, and fragile materials, leaving the best finish. Also, use them to debur rough cut or sawn edges.

Our Rotaries have an integral arbor, enabling them to be used in reversible drive tools.
They allow the user to cut a wide range of materials quickly and cleanly leaving an excellent finish. All rotaries are ideal for routing, shaping and removing materials without tearing or clogging.
Use on all Woods, Glass Fibre, Carbon Fibre, PCB, Kevlar, Plexiglas, Lexan, Perspex, Acrylics, Plastics, Polystyrene, Ceramics etc.
Excellent on Perspex, Plexiglass, Lexon, use below 10,000 RPM and they will not melt, crack or chip them. (not recommended for use on metal)
Note Rotaries should be fully inserted in to the chuck and tightened before using. Maximum RPM 20,000 Low - Medium.
SAFETY:- Always wear protective goggles when using Rotary Tools.
IMPORTANT:- Carbon Fibre should not be cut using an electric drill, because of the possibility of electrocution.

10.05 12.06


Quantity: 





Wide Cone (Ref: RF2..)

Wide Cone

Available in Fine or Coarse

10.05 12.06


Quantity: 





Drum (Ref: RF3..)

Drum

Available in Fine or Coarse

10.05 12.06


Quantity: 





Pancake (Ref: RF..)

Pancake

Available in Fine or Coarse

Small Rotary
Rotary Pancake Fine finishing Grit 20 mm. Shaft / arbor 3.1 mm (1/8").
Cuts on end face, make and smooth out hollows.

The FINE ROTARIES enables the user to cut thin, and fragile materials, leaving the best finish. Also, use them to debur rough cut or sawn edges.

Our Rotaries have an integral arbor, enabling them to be used in reversible drive tools.
They allow the user to cut a wide range of materials quickly and cleanly leaving an excellent finish. All rotaries are ideal for routing, shaping and removing materials without tearing or clogging.
Use on all Woods, Glass Fibre, Carbon Fibre, PCB, Kevlar, Plexiglas, Lexan, Perspex, Acrylics, Plastics, Polystyrene, Ceramics etc.
Excellent on Perspex, Plexiglass, Lexon, use below 10,000 RPM and they will not melt, crack or chip them. (not recommended for use on metal)
Note Rotaries should be fully inserted in to the chuck and tightened before using. Maximum RPM 20,000 Low - Medium.
SAFETY:- Always wear protective goggles when using Rotary Tools.
IMPORTANT:- Carbon Fibre should not be cut using an electric drill, because of the possibility of electrocution

10.05 12.06


Quantity: 





Domehead (Ref: RF5..)

Domehead

Available in Fine or Coarse

10.05 12.06


Quantity: 





3MM Rod (Ref: RF6....)

3MM Rod

Available in Fine or Coarse

10.05 12.06


Quantity: 





Inverted Cone (Ref: RF7..)

Inverted Cone

Available in Fine or Coarse

10.05 12.06


Quantity: 





9MM Dia Ball (Ref: RF8..)

9MM Dia Ball

Available in Fine or Coarse

10.05 12.06


Quantity: 





Ultra Fine Countersink (Ref: RF9UF)

Ultra Fine Countersink

6MM dia countersink in Ultra fine only

10.05 12.06


Quantity: 





9mm Countersink (Ref: RF10..)

9mm Countersink

Available in Fine or Ultra Fine

10.05 12.06


Quantity: 








Perma-grit Rotary Files for Dremel Proxxon etc - Buy online at Chronos (call us or click live chat for help with Perma-grit Rotary Files for Dremel Proxxon etc)
Visit our engineering blog